INSTEON Micro Dimmer Module 2442-222

$ 59.99

Turn Any Wall Switch Into an INSTEON Remote Controllable Dimmer

Overview

  • Wires in behind your existing switches or fixtures
  • Sense wires allow for control via a connected, hard-wired switch
  • Compatible with latching, single momentary and dual momentary switches
  • Programmable on-level and ramp rate
Essential Info

Adding remote control to wired lights usually means replacing switches, not any more. With INSTEON's new dual-band Micro Dimmer Module, you can keep your existing antique, toggle or decorative wall switches while adding the customizable, dimmable remote control functionality of a SwitchLinc Dimmer. Customize your lights with a preset brightness level and ramp rate, then control it from any INSTEON controller. This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch by way of sense wires. Connect the sense wires to any style wall switch to match any type of designer theme (antique, push-button, metal, etc.) Micro Dimmer is also so small that it can be installed as an in-line module within a fixture box, providing remote control dimming without having to run wires to a wall switch. INSTEON also offers a Micro On/Off Module and a Micro Open/Close Module.

More Info

INSTEON Micro Dimmer is compatible with latching, single momentary and dual momentary switches. By default, it comes programmed for latching switches such as paddles and toggles; it is easily configured for single and dual momentary switches with a simple reprogramming procedure during installation. Due to its hidden nature, we highly recommend using a home automation controller to manage Micro Open/Close.

General

Product Name: INSTEON Micro Dimmer

Brand/Manufacturer: INSTEON

Manufacturer Product No.: 2442-222

UPC: 813922012705

Warranty: 2 years, limited

INSTEON

INSTEON: Controller and responder

Maximum links/scenes: 400

Load brightness levels: 32 locally (256 with software)

Status LED: Green when load is on, red when load is off, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software),Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software)

LED brightness: Adjustable from off to 100% bright

Local on-level: Adjustable from 32 fixed brightness levels or resume dim

Local ramp rate: Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 9 minutes with software)

Local control: Yes

Commands supported as controller: On, Off, Fast on, Fast off, Begin brighten, End brighten, Begin dim, End dim

Commands supported as responder: On, Off, Fast on, Fast off, Begin brighten, End brighten, Begin dim, End dim, Incremental brighten, Incremental dim, Beep

Software configurable: Yes

Ramp Rates (full-ON to full-OFF): 0.125 to 9 seconds if programmed locally, 0.125 seconds to 8 minutes if programmed remotely via software

RF range: 150 feet open air (may vary due to local interference)

Phase detect beacon: Yes

X10 support: Yes

X10 addresses: Any 1 of 256 (unassigned by default)

INSTEON device category: 0x01 dimmable lighting control (all frequencies)

INSTEON device subcategory: 2442-222 (915MHz), 0x35

Mechanical

Mounting: Behind switch or above light fixture in single-gang electrical box

Wire connections: Sense 1 (yellow): 24 AWG, 0.205mm, Sense 2 (purple): 24 AWG, 0.205mm

Screw clamp connections: Line, Load, Neutral 1, Neutral 2

Case color: White

Set button: Yes

Plastic: UV stabilized ABS+PC

Beeper: Yes

Beep on button press: Beeps when button is pressed or connected switch is tapped (must be enabled via software)

LED: 1 RGB

Dimensions: 1.8"H x 1.8"W x 0.7"D

Weight: 2.52 oz

Operating environment: Indoors

Operating temperature range: 32° to 104°F (0° to 40°C)

Operating humidity range: 0-90% relative humidity

Storage temperature range: -4° to 158°F (-20° to 70°C)

Electrical

Voltage: 100VAC to 240VAC

Frequency: 50/60Hz auto-detected at power-up

Load: Min. 5W, Max. 200W (at 240VAC), Min. 5W, Max. 100W (at 140VAC)

Load types: Incandescent

Hardwired remote control: Yes, either latching or momentary switches supported

Retain all settings without power: Yes, saved in non-volatile EEPROM

Standby power consumption: <1W

Safety approved: ETL, CE, C-Tick

Certifications: FCC, UL, IEC, EN

FCC ID: SBPMM01 

 

Customer Reviews

Based on 1 review Write a review
Innovative Home Systems is an Upfront Merchant on TheFind. Click for info.