INSTEON Micro On/Off Module 2443-222

• Pin It

Turn Any Wall Switch Into an INSTEON Remote Controllable Switch

Overview

• Add remote control to virtually any switch or outlet
• The smallest inline module ever! Fits into almost all boxes
• Turn your antique, custom color or non-standard wall switches into home automation switches
• Wire in behind your existing switches, outlets and above your light fixtures
• Sense wires allow for control via a connected, hard-wired switch
• Compatible with latching switches as well as single momentary and dual momentary switches

Essential Info

Adding remote control to wired lights usually means replacing switches, not any more. With INSTEON's new dual-band Micro On/Off Module, you can keep your antique, toggle or decorative wall switches while adding the same remote control functionality of SwitchLinc. This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch by way of sense wires. Connect the sense wires to any style wall switch to match any type of designer theme (antique, push-button, metal, etc.) Micro On/Off is so tiny that it can be installed as an in-line module within a fixture box, providing remote control without having to run wires to a wall switch. INSTEON also offers a Micro Dimmer Module and a Micro Open/Close Module.

More Info

INSTEON Micro On/Off is compatible with latching, single momentary and dual momentary switches. By default, it comes programmed for latching switches such as paddles and toggles; it is easily configured for single and dual momentary switches with a simple reprogramming procedure during installation. Due to its hidden nature, we highly recommend using a home management controller INSTEON Hub to manage Micro Open/Close.

General

Product Name: INSTEON Micro On/Off

Brand/Manufacturer: INSTEON

Manufacturer Product No.: 2443-222

UPC: 813922012736

Warranty: 2 years, limited

INSTEON

INSTEON: Controller and responder

Maximum links/scenes: 400

Status LED: Green when load is on, red when load is off, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software), Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software)

LED brightness: Adjustable from off to 100% bright

Local control: Yes

Commands supported as controller: On, Off, Fast on, Fast off, Begin brighten, End brighten, Begin dim

End dim Commands supported as responder:

On, Off, Fast on, Fast off, Beep

Software configurable: Yes

RF range: 150 feet open air (may vary due to local interference)

Phase detect beacon: Yes

X10 support: Yes

X10 addresses: Any 1 of 256 (unassigned by default)

INSTEON device category: 0x02 switched lighting control (all frequencies)

INSTEON device subcategory: 2443-222 (915MHz), 0x2F

Mechanical

Mounting: Behind switch or outlet, or above light fixture in single-gang electrical box

Wire connections: Sense 1 (yellow): 24 AWG, 0.205mm², Sense 2 (purple): 24 AWG, 0.205mm²

Screw clamp connections: Line, Load 1, Load 1 (second terminal), Neutral

Case color: White

Set button: Yes

Plastic: UV stabilized ABS+PC

Beeper: Yes

Beep on button press: Optional (off by default), requires software to enable

LED: 1 RGB

Dimensions: 1.8”H x 1.8”W x 0.7”D

Weight: 2.52 oz

Operating environment: Indoors

Operating temperature range: 32° to 104°F (0° to 40°C)

Operating humidity range: 0-90% relative humidity

Storage temperature range: -4° to 158°F (-20° to 70°C)

Electrical

Voltage: 100VAC to 240VAC

Frequency: 50/60Hz auto-detected at power-up

Load types: Resistive, Inductive/capacitive, Low voltage halogen

Hardwired remote control: Yes, either latching or momentary switches supported

Retain all settings without power: Yes, saved in non-volatile EEPROM

Standby power consumption: <1W

Safety approved: ETL, CE, C-Tick

Certifications: FCC, UL, IEC, EN

FCC ID: SBPMM01